How To Clean The Hood Of The Stove Without Removing The Paint

Download Article

Download Commodity

Whether you call it an extractor hood, range hood, kitchen hood, cooking canopy, extractor fan, whatever...Its main purpose is to remove the air associated with cooking. That air can comprise grease, oestrus, odors, and steam. There may come up a time when you lot have to supercede or permanently remove a range hood. Although these instructions won't apply to every kind of hood fan, they will provide an overview of the process.

Steps Download Article

one

Please read this commodity completely earlier beginning.
ii

Disconnect power source. Many range hoods are powered by a circuit other than the 1 that supplies an electric range. In the U.S., almost electric ranges are 208 or 240 volt types. Most range hoods are 120 volt. 1 single pole (single width) excursion breaker or fuse will likely provide power for the range hood. 240 volt electric ranges by contrast, will likely be supplied by ane ii pole (double width) excursion billow or two cartridge fuses. Turn the fan and lite (if equipped) of the range hood on, and have a helper turn circuits off and and so dorsum on until the fan and light both shut off. If unable to locate the circuit, turning off the service disconnect or main should shut power off to the entire house.

Advertisement
3

Make room to work. Move the electric range if located nether the hood if possible. Gas and propane ranges are oft likewise heavy to move hands or without damaging the floor. Regardless of type, exist enlightened of the length of power cord sets and any flexible gas line. Electrical ranges are often provided with cord sets that allow easy insertion and removal from a receptacle. Gas and propane lines however, should not be loosened or disconnected unless done past licensed professional. Many newer gas and propane ovens and ranges as well take electrical connections via cord sets, too.
iv

Inspect the surface area directly higher up the hood. This may be a cabinet or other storage expanse that tin provide a not bad bargain of information every bit to how the hood is secured, powered and ducted (in the example of ducted units only).
5

Remove all covers, filters, light bulbs, etc. Many times, range hoods are held past 1 or more fasteners that may be hidden behind these objects.
6

Place wiring connections. One of the covers removed above should provide access to the field wiring compartment. This is where the house power is brought into the range hood and continued to information technology. Label every wire with a number written on masking tape (or other method), if it is to be reinstalled after. Apply a scheme that works best such as color coding, numbers, messages or even a photo taken with a prison cell telephone. Make sure that information technology is clear enough to empathize days or weeks later when it is time to reconnect.
7

Disconnect wiring. More often than not, white, black and possibly a green or bare wires from the hood are continued to like colors of wires from a cable or conduit with wirenuts or other connector designed for the purpose. Since the wires take been identified in the previous pace, this will not exist of business organization. Simply unscrew wirenuts or other devices, cutting off any wires connected with crimped connectors as shut to the connector to leave as much wire as possible.
8

Remove cable or conduit connector. Spin the locknut off any fitting holding the cable or conduit to the wiring compartment. Some fittings prune in instead. If unable to remove the fitting from the hood, information technology might be possible once the hood is no longer secured to the mounting surface, after.
9

Remove fasteners. With a helper providing support to the hood, remove all but 2 fasteners. Leave ii fasteners at reverse ends of the hood in place. Merely loosen these two enough to peer into the void between the support surface and the hood to run across how the unit is powered, etc. (this is peculiarly helpful if unable to admission the space above the hood, outlined in an earlier step).
10

Support the hood. Have a helper hold the hood while the terminal two screws are removed. Most home center variety hoods are non very heavy, but are bulky. Trying to remove fasteners while holding the hood at the aforementioned time can be done if no other options are available, but is much easier with a helper. Custom or specialty hoods may be extremely heavy depending on construction materials used and physical size of the unit of measurement.
eleven

Resolve complications. The hood volition be continued merely by the power source cable or conduit (if unable to disconnect in previous steps above) or duct work (if provided). Utilise the ability to admission connectors and fittings above and below to allow the hood to be pulled away from the power source. Check for the presence of screws used to connect the hood to whatever duct work, and remove them. The hood should now be able to be moved freely.
12

Terminate the hood power source. Install an approved electrical switchbox if the range hood will not exist used again, otherwise individually cap the ends of the wires securely with wirenuts so that they will non crusade shock if contacted while ability is on.
13

Restore power. If the service disconnect or primary was turned off, or if the hood is role of another circuit that is needed, the fuse(due south) or circuit breaker(s) will need to be returned to the on position. Be certain to safely stop the wires as described above earlier performing this step.

Advertisement

Add together New Question

Question

Are wire nuts and marrette the same thing?

No, they are not.

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertizement

"Vented" and "Ducted" depict hoods that draw vapors, steam, smoke, etc. through a filter and exhaust the filtered air through duct work directly outdoors.
Remove unused duct work where accessible. Block the duct work with viii or more inches of insulation to help prevent unwanted drafts. Consider removing the duct grill work or grates on the exterior of the habitation if it will not be used once again.
Nigh newer "under cabinet" type range hoods are ductless or ventless, but can easily be converted to ducted or vented type by removing a pre-punched 3" ten ten" rectangular or vii" round metal plate to connect to the duct work. It requires much more endeavor to return it to ductless or ventless style every bit the hole will need to be covered upward.
"Ventless" and "Ductless" draw hoods that draw vapors, steam, smoke, etc. through a filter and frazzle the filtered air back into the same room through openings on the front end of the range hood. No duct work is needed.

Thanks for submitting a tip for review!

Advertising

Range hood filters require regular cleaning. Grease and oils are trapped on the surface of the filter, reducing the amount of air that tin be drawn through the filter. Eventually the filter will clog and present a fire take a chance.
Operating the hood without a filter results in grease and oils collecting on the fan blades and the interior of the range hood and duct work (if installed). These deposits of grease and oil are a burn hazard, and will result in loss of remainder of the fan blades. This imbalance usually results in noisy operation and early motor failure due to overheating.

Things You'll Demand

Helper
Screwdrivers
Pliers
Wire cutters
Wirenuts
Erstwhile work switchbox (if not reinstalling)
Battery drill with phillips & straight screwdriver tips (optional)
Flashlight

Virtually This Article

Thanks to all authors for creating a page that has been read 111,937 times.

Did this commodity help you?